Top 3 Best Octocopter Power Distribution Board PDB


Top 3 Best Octocopter Power Distribution Board PDB

Octocopter Power Distribution Board

Octocopter Power Distribution Board

Drone power distribution board is an essential component for the flying drone or quadcopter. Here we show some of the best Octocopter Power distribution board so that you can improve or customise your drone for future flights.

 Octocopter Power Distribution Board

  • If you love Radio Control products, then we’re just like you.
  • We’re always developing and sourcing new model products and then bringing them to you.
  • All the items shipped from USA. Including a receipt in the package for custom if need.
  • Customer service is our top priority, and while some issues are beyond our control, we do our best to ensure your transaction exceeds your expectations.
  • Should you have an issue with any of our products or service, please contact us vis message.

Designed in house by the HobbyKing Enginerds, this handy power distribution board has the same foot print as our Multri-rotor control boards and is the ultimate solution for tidy power distribution wiring. Simply use 3.5mm male connectors on your ESCs and plug a battery in. The PCB is Gold plated for optimality efficiency and also features a bling port (aka 2 pin JST size auxiliary power out) Perfect for powering LEDs or any accessory fitted to your Octocopter.Features.Current:8 x 10A Outputs (MAX)Power Input: XT60 with 12AWG wireMotor output:8 x 3.5mm Female bullet plugAux output: 2 pin JST compatibleWeight: 36.0g (including wires)

 

Quadcopter Power Distribution Board XT60 XT-60 20a Quad Mutlicopter 

  • Current: 4 x 20A Outputs (MAX)
  • Power Input: XT60 with 12AWG wire
  • Motor output: 4 x 3.5mm Female bullet plug
  • Aux output: 2 pin JST compatible
  • Weight: 27.3g (including wires)

his handy power distribution board has the same foot print as our Multri-rotor control boards and is the ultimate solution for tidy power distribution wiring. Simply use 3.5mm male connectors on your ESCs and plug a battery in. The PCB is Gold plated for optimality efficiency and also features a bling port (aka 2 pin JST size auxiliary power out) Perfect for powering LEDs or any accessory fitted to your Quadcopter.

PDB Power Distribution Board Mini Power Hub with BEC 5V & 12V for Multicopter Quadcopter

 

  • The Mini power distribution board PDB HUB has been engineered to provide the highest possible performance and reliability in a 36*36mm & 4 layers PCB.
  • The PDB HUB also features convenient solder bridge of various voltage for camera & video transmitter.,well laid out and easy to set up.
  • It is specially made for the Multi-Rotors, mini FPV Quad. Built-in 5V BEC can be connected to receiver or flight controller with Aux pins directly.
  • Simplify wiring. If the battery is 4~6 cells LiPo, the BEC can be set to 12V output, to power the Gimbals, Video Transmitters, etc.
  • Full featured mini power distribution board, gives plenty of ouput options,it is easy to solder on and and desolder.

Features:
– 2oz copper & 4-layers PCB.
– ESC & Battery solder tabs in pairs
– Solder Bridges of various voltage for Camera & VTX.
– DC/DC synchronous buck regulator, Efficiency is up to 95%.
– TVS(Transient Voltage Suppressor) protection for DC/DC chip.
– 5V & 12V Output LED indicators & Short circuit tolerant
Specification:
General:
– Input voltage range (2S-6S operation): 7.2 – 26VDC
– Regulated 5V and 12V outputs
– LED power indicators ( 5V & 12V outputs )
– 4 ESC outputs
ESC outputs:
– Continuous current: 20A per output
– Peak current (10 seconds/minute): 30A per output
BEC 5V output:
– Designed for RC Receivers, Flight controllers, OSD, and Servos.
– Voltage: 5.0 +/- 0.1VDC
– Continuous current: 3 Amps
– Short-circuit tolerant (10 seconds/minute)
– LED (indicates voltage is in regulation, within 10%)
BEC 12V output:
– The battery should be 4S~6S LiPo
– Standard output designed to power cameras and video transmitters,etc.
– Voltage: 12.0 +/- 0.2VDC
– Continuous current: 2 Amps (Max.3A 10s/minute)
– Short-circuit tolerant (10 seconds/minute)
– LED (indicates voltage is in regulation, within 10%)
CAM & VTX voltage bridge
– 3S operation. choose VCC for 12V camera & 12V VTX, VCC=Battery Voltage.
– 4~6S operation, choose 12 for 12V camera & 12V VTX
– 3~6S operation, choose 5 for 5V camera
– Video pass through from the CAM pad to the VTX pad
Physical:
– Dimensions: 36 x 36mm
– Weight: 6g
– Mounting holes 30.5mm square spacing
Package including :
1 x Power Distribution Board PDB


Leave a Reply

Your email address will not be published. Required fields are marked *