Top 5 Best Quadcopter Power Distribution Board


Top 5 Best Quadcopter Power Distribution Board

 

A quadcoper power distribution board “pdb” is a part essential in a drone or quadcopter. Here we show some of the best sellers power distribution board for drones and quadcopters:

Quadcopter Power Distribution Board XT60 XT-60 20a Quad Mutlicopter 3.5mm

  • Current: 4 x 20A Outputs (MAX)
  • Power Input: XT60 with 12AWG wire
  • Motor output: 4 x 3.5mm Female bullet plug
  • Aux output: 2 pin JST compatible
  • Weight: 27.3g (including wires)

This handy power distribution board has the same foot print as our Multri-rotor control boards and is the ultimate solution for tidy power distribution wiring. Simply use 3.5mm male connectors on your ESCs and plug a battery in. The PCB is Gold plated for optimality efficiency and also features a bling port (aka 2 pin JST size auxiliary power out) Perfect for powering LEDs or any accessory fitted to your Quadcopter.

 

PDB XT60 Power Distribution Board BEC 5V 2A 12V 0.5A with XT60 Plug for DIY Quadcopter Output Support 6 ESC for X or H Design FPV Racing Quad

 

  • The PDB-XT60 has been engineered to provide the highest performance and reliability in a 36*50mm & 4 layers PCB.
  • It distributes power from a LiPo pack to 6 ESCs, as well as providing synchronised & regulated DC 5V outputs & linear regulated DC 12V for powering Cameras, Servos, RC receiver, Flight Controllers, Video Transmitters, LEDs, etc.
  • Total 6 pairs ESC solder tabs are fit for H or X type frame
  • 5V & 12V Output LED indicators & Short circuit tolerant
  • Mounting hole Suit for CC3D naze32 SP Racing F3 FC

Matek PDB-XT60 w/BEC (5V and 12V) This Power Distribution Board has been engineered to provide the highest possible performance and reliability in a 36x50mm, 4 layer PCB. It comes with an XT60 for easy connection to LiPoly batteries. Using BECs it distributes power from 3~4S LiPoly packs to 6 ESCs, as well as providing synchronized and regulated DC 5V outputs for RC Receivers, Flight controllers, OSD, and Servos. It also provides linear regulated DC 12V for powering Cameras, Servos, RC receiver, Flight Controllers, Video Transmitters, LEDs, etc. A great package to get your Racing Drones powered up and racing. Features: • 2oz copper, 4-layers and 1.6mm PCB • Built-in XT60 Socket • Total 6 pairs ESC solder tabs are fit for H or X type frame • 5V and 12V Output LED indicators • Regulated 5V and 12V outputs • Short circuit tolerant Specs: Input voltage range: 9 – 18V DC (3S-4S LiPoly operation) Output continuous current: 25Ax4 or 15Ax6 Output Peak current (10 seconds/minute): 30Ax4 or 20Ax6 BEC 5V output: 5V/2A (Max.2.5A 10s/minute) Output Ripple: 40mV (VIn= 16V, VOut= 5V@2A load) Short-circuit tolerant: 5 seconds/minute BEC 12V output (4S LiPoly, 13~18V DC): 12V/500mA (Max.0.8A 5s/minute) BEC 12V output (3S LiPoly): =3S LiPoly voltage – 1V Dimensions: 36 x 50 x 4 mm (without XT60) Mounting: 30.5 x 30.5mm, Φ3mm Weight: 7.5g (w/o XT60), 11g (w/ XT60)

 

FPVDrone Matek V3.1 PDB Power Distribution Board Mini Power Hub with BEC 5V & 12V for Multicopter Quadcopter

 

  • The Mini power distribution board PDB HUB has been engineered to provide the highest possible performance and reliability in a 36*36mm & 4 layers PCB.
  • The PDB HUB also features convenient solder bridge of various voltage for camera & video transmitter.,well laid out and easy to set up.
  • It is specially made for the Multi-Rotors, mini FPV Quad. Built-in 5V BEC can be connected to receiver or flight controller with Aux pins directly.
  • Simplify wiring. If the battery is 4~6 cells LiPo, the BEC can be set to 12V output, to power the Gimbals, Video Transmitters, etc.
  • Full featured mini power distribution board, gives plenty of ouput options,it is easy to solder on and and desolder.

Features:
– 2oz copper & 4-layers PCB.
– ESC & Battery solder tabs in pairs
– Solder Bridges of various voltage for Camera & VTX.
– DC/DC synchronous buck regulator, Efficiency is up to 95%.
– TVS(Transient Voltage Suppressor) protection for DC/DC chip.
– 5V & 12V Output LED indicators & Short circuit tolerant
Specification:
General:
– Input voltage range (2S-6S operation): 7.2 – 26VDC
– Regulated 5V and 12V outputs
– LED power indicators ( 5V & 12V outputs )
– 4 ESC outputs
ESC outputs:
– Continuous current: 20A per output
– Peak current (10 seconds/minute): 30A per output
BEC 5V output:
– Designed for RC Receivers, Flight controllers, OSD, and Servos.
– Voltage: 5.0 +/- 0.1VDC
– Continuous current: 3 Amps
– Short-circuit tolerant (10 seconds/minute)
– LED (indicates voltage is in regulation, within 10%)
BEC 12V output:
– The battery should be 4S~6S LiPo
– Standard output designed to power cameras and video transmitters,etc.
– Voltage: 12.0 +/- 0.2VDC
– Continuous current: 2 Amps (Max.3A 10s/minute)
– Short-circuit tolerant (10 seconds/minute)
– LED (indicates voltage is in regulation, within 10%)
CAM & VTX voltage bridge
– 3S operation. choose VCC for 12V camera & 12V VTX, VCC=Battery Voltage.
– 4~6S operation, choose 12 for 12V camera & 12V VTX
– 3~6S operation, choose 5 for 5V camera
– Video pass through from the CAM pad to the VTX pad
Physical:
– Dimensions: 36 x 36mm
– Weight: 6g
– Mounting holes 30.5mm square spacing
Package including :
1 x Power Distribution Board PDB

 

CC3D Naze32 Flight Controller Mini Power Distribution Board PDB w/LED (Comes with BEC 5V-12V output) for 250 Multicopter

 

  • This power distribution board (PDB) can be used on CC3D Naze32 flight controller.
  • Suitable for mini racing drone quadcopters, such as QAV250, ZMR 250, ARRIS FPV 250, etc.
  • It is great for those who are running ESC without a BEC to power the flight controller board and other various electronics on your Mulitrotor.
  • With two BEC output, 5V and 12V. Weighs only 6g. The LED switch is used to turn the LED lights on&off.
  • We have another upgraded PDB with more functions, such as OSD, LC filter, etc. Search this ASIN on amazon: B01H6MG4OK

Description:
This item is a power distribution board for CC3D flight controller specially made by ARRIS, featuring mini size and light weight. It has exactly same size and hole location with CC3D.

Features:

With two BEC output, 5V and 12V
Comes with LED switch
Input Voltage: 2-6S
Weight: 6g
Suitable for: 250 mini racing quadcopters, such as QAV250, tarot TL250, etc.

Package included:
1 x ARRIS CC3D Flight Controller Distribution Power Board

 

PDB Board Power Distribution Board PDB-XPW 140A & Dual BEC 5V/2A 12V/0.5A for X Type Frame FPV Racing Drone

 

  • The PDB-XPW distributes power from a LiPo Pack to 4 ESCs, as well as providing synchronised Regulated DC 5V out puts linear regulated DC 12V for powering cameras, RC receiver,Flight Controller, Video Transmitters, LEDs, etc
  • Built-in current sensor 140A,and provides an XT60PW socket to facilitate the LiPo package power supply
  • Specially design for X Type Drone with a XT60PW socket, it is convenient to connect the Lipo pack for X Type drone frame, such as QAV X X250 X220 X210 X180 Drone Frame, and so on
  • 5V & 12V Output LED indicators & Short circuit tolerant
  • Manual website: http://www.mateksys.com/downloads/PDB-XPW_Manual.pdf

Specifications:
Input voltage range (3S-5S LiPo operation): 9 – 21V DC
PDB: 4 x 35A
Regulated 5V and 12V outputs
Current module 140A
LED power indicators ( 5V & 12V outputs )
Current Module
140A
3.3V ADC
BEC 5V output:
Designed for RC Receivers, Flight controllers, OSD, and Servos
DC/DC synchronous buck regulator
Voltage: 5.0 +/- 0.1VDC
Continuous current: 2 Amps (Max.2.5A 10s/minute)
Output Ripple: 40mV (VIn=16V, VOut=5V@2A load)
Short-circuit tolerant (5 seconds/minute)
BEC 12V output:
Designed for Video TX or FPV camera with linear regulator
The battery should be 4~5S LiPo (13~21V DC)
Voltage: 12.0 +/- 0.3VDC
Continuous current: 500mA (Max.0.8A 5s/minute)
Short-circuit tolerant (2 seconds/minute)
BEC 12V @ 3S LiPo
Output voltage= 3S LiPo voltage -1.5V
Physical:
Mounting: 30.5 x 30.5mm, Φ3mm
Dimensions: 36 x 50 x 4 mm (w/o XT60PW), 36 x 58 X10.5mm (w/ XT60PW)
Weight: 8.5g(w/o XT60PW), 13g(w/ XT60PW)

Package include:
1 * PDB-XPW
1 * XT60-PW
4 * M3 x12
4 * m3 x6+6
8 * M3 nuts


Leave a Reply

Your email address will not be published. Required fields are marked *